Shower Won’t Stop Running: Causes and Fixes – High Shower
If your shower continues to drip or not stop even when shutting off the water, it isn’t very pleasant, in addition to significantly increasing the cost of electricity and water. The root of the issue determines the solution to such a problem, and it could result from various issues.
If your shower doesn’t stop running, it could be due to an insight faucet, a damaged or defective cartridge, or a valve. If you want to fix a shower that doesn’t stop working, ensure the faucet is tightened and replace the damaged valve or cartridge. These are the solutions that can be done at home using the appropriate equipment and the correct replacements for the valve and cartridge.
The water is coming out of the shower head after turning it off
Your plumbing system comprises various gaskets and seals, cartridges, and valves that stop the water from flowing when you don’t require it to and allow it to flow whenever you require it to. If one of these components isn’t functioning properly, your shower won’t stop running despite having switched the shower off.
There are a variety of reasons your shower doesn’t shut off, including:
1. Loose faucet
The shower faucets (and most faucets) come with a screw inside the handle that secures them. To allow the faucet to switch the water off and on without leaks, the screw has to be tightest. If the faucet screw has become loose, your faucet will not have enough strength to ensure the tightest seal when shutting off the water. This can lead to leaks inside the faucet head.
Sometimes the shower faucet will not shut off because the screw that holds the handle is damaged or loose. Sometimes the shower faucet doesn’t shut off completely because it’s loose or stuck and sliding off. If you’re noticing that the shower faucet isn’t turning on, regardless of how many attempts you try, the problem is a stuck or loose faucet screw could be the reason.
2. The valve or cartridge is damaged or defective.
Shower cartridges control the flow and temperature of the water when you turn the handle. The shower valve also regulates the flow and temperature of the water, and they are utilized interchangeably.
If the valve or cartridge is damaged or damaged, water from the main source will continue flowing into the showerhead even after turning off the showerhead. This is because the valve or cartridge doesn’t ensure a secure seal on the knob that controls the showerhead.
How can you repair a shower that will not end?
The solutions to these issues are:
1. Make sure you tighten the faucet
It is possible to tighten the shower faucet using the following method:
Switch off the water supply from the main supply to the bathroom.
Use a flat-blade screwdriver or another sharp tool to open the cover plate of the faucet.
Close the screw on the handle underneath the cover using either a spanner or screwdriver, according to the requirements.
Install the cover plate back on the faucet.
The water should be turned on at the mains, then turn off the faucet to determine whether the solution worked.
It was successful if you don’t notice the shower running or other leaks. If the shower doesn’t turn off completely, you can repeat the procedure of tightening the faucet, but do it correctly now.
2. Replace the valve or cartridge
To replace the damaged cartridge or valve, Follow these steps:
To begin, turn off the water on the main connection to the bathroom. You can verify if it works by turning on any faucet or taps in the bathroom.
Cover the shower drain with a towel to ensure you don’t lose any screws or other small pieces when working.
Locate the cover plate that is on the faucet, then push it off by using a sharp object.
The screw, or the nut around it counterclockwise until it is released. Also, remove the handle.
The screw is the one that holds the cartridge in place. It will allow you to remove this cartridge by pulling it away. Be careful not to do this, as you risk getting rid of the tiny parts, such as the clip, can be utilized with that new cartridge.
Use the lubricant included with the new cartridge, or choose one you have made yourself.
Ensure the cartridge is aligned with the cold and hot parts of the water intake exactly the same way as the one you took out.
Place the cartridge in the handle and then the bolt in the handle’s center. The bolt should be tightened by turning it clockwise until it’s secure.
The same procedure can be employed for replacing the shower valve, as it is the correct shower valve to fit your bathroom. You can check the quality of the new shower valve by turning off the main water and off the shower tap.
If the shower valve snapped off and did not run the water, you should swap the handle for a brand new one by shutting off water from the mains using a wrench to pull out the damaged handle and then replace it by installing the replacement one. You must also ensure that the proper shower valve size is used during this method. Then, you can turn on the water.
Why do my shower and tub are running at the same time?
If your tub doesn’t flow when you turn off the water, the issue is likely due to a malfunctioning shower diverter valve. The valve controlling the shower diverter regulates how much water flows from the shower to the tub spout so that only one works at any time. If it’s damaged or clogged or is malfunctioning due to one cause or another, the water could flow into the tub and shower simultaneously or not at all.
You can resolve the issue of water leaking out of the shower and tub in one go by following the following steps:
- Stop the water supply in the mains that connects to the bathroom.
- The shower diverter valve can be opened by removing nuts, bolts, and screws.
- Verify if it’s damaged or blocked.
- If it is blocked, scrub it with an easy brush and blast air.
- If the item is damaged If it is damaged, replace it with one that is the exact size and type.
- This should bring back the normal functioning of your tub and shower.
- Moen’s shower will not turn off.
If a Moen shower does not turn off, the reason is an issue with the cartridge that needs replacement. The procedure for replacement differs for different types of cartridges. The procedure for replacing it is as follows:
Shut off the water source at the mains, then stop the drains by covering them to protect the smaller parts.
Remove the plastic from the base of the valve until you can get to the screw located at the center of the hand.
With a screwdriver, remove the screws that hold the plate in place and then remove the plate off the wall. The plate can be gradually removed from the wall using the help of a screwdriver or another flat piece of equipment.
- Slide the stop tube out of the cartridge by pulling it toward you.
- Take the U-shaped valve out of the valve’s body with two pliers.
- Take care to slide the spacer washer off of the shaft and set it aside.
Look over the box for the cartridge to find the nut-like device in white color. This tool must be slipped onto the shaft to make it interlock with the original cartridge. While holding this toll, using pliers, move it around in back-and-forth movements until the cartridge has been removed from the body. Take the tool off using the pliers and use the pliers to grab the cartridge, pulling it away from the valve.
Remove the new cartridge, then insert it inside the valve until the last moment. Place the nut tool over the cartridge and use it to align it to the body of the valve. The ears on the cartridge should be on the top and bottom.
Reattach the retainer clip in the shape of a U onto the body of your valve, and secure it with a snap. Be sure to check for an opening or snap; otherwise, adjust the cartridge before trying another time.
Reinstall the rest of the pieces, such as the knob for the faucet, in the same order they were removed.
Verify the reliability of the brand-new unit by switching on the mains and then checking whether there are leaks after you shut off the switch. If Moen shower heads like Moen Magnetix become very popular, this method can help maintain them for longer.
Leave a Reply